on Monday I droped the front of my truck and it looks pretty sweettry to get some pics today, Thanks to Ontariov8 as he hooked me up with the front I-beams!!!
When I put my new shocks on I snaped the bolt. any ideas how to replace this or do I have to replace the whole radious arm?
droped front
Moderator: MalcolmV8
-
- Posts: 357
- Joined: Wed Jun 20, 2007 1:16 pm
- SM: No
- Location: Toronto, ON, Canada
droped front
'93 ranger ext cab 5.0L HO lorider
- MalcolmV8
- Supporting Member
- Posts: 2597
- Joined: Fri Dec 10, 2004 4:50 pm
- SM: Yes
- Location: Kansas City, MO
I did that once many years ago and now I soak those nuts in PB Blaster and use a torch to heat them before turning them off if need be. I replaced the radius arm but you could probably get one welded on or drill a hole and run a bolt all the way through.
92 302 Ranger - sold
94 302 Ranger AWD - sold
07 BMW 335xi - tuned, boost turned up, E85 - sold
04 911 TT - to many mods to list. Over 600 All Wheel HP on pump gas - sold
2015 Coyote - daily driver
03 Cobra - 2.3 TVS on a built 12:1 CR motor with ported heads, cams, long tubes etc.
MD Racing Lean Protection Module
E85
Tuned by MD Racing
https://www.youtube.com/c/MalcolmV8
94 302 Ranger AWD - sold
07 BMW 335xi - tuned, boost turned up, E85 - sold
04 911 TT - to many mods to list. Over 600 All Wheel HP on pump gas - sold
2015 Coyote - daily driver
03 Cobra - 2.3 TVS on a built 12:1 CR motor with ported heads, cams, long tubes etc.
MD Racing Lean Protection Module
E85
Tuned by MD Racing
https://www.youtube.com/c/MalcolmV8
-
- Posts: 357
- Joined: Wed Jun 20, 2007 1:16 pm
- SM: No
- Location: Toronto, ON, Canada
- MalcolmV8
- Supporting Member
- Posts: 2597
- Joined: Fri Dec 10, 2004 4:50 pm
- SM: Yes
- Location: Kansas City, MO
Bummer. Must have tightened the heck out of it or it was rusted bad and ready to snap anyways.
I'd use a grade 8 bolt and a lock nut. In fact after running a bolt through I'd probably weld it on the back side so it is essentially a stud just like from the factory.
I'd use a grade 8 bolt and a lock nut. In fact after running a bolt through I'd probably weld it on the back side so it is essentially a stud just like from the factory.
92 302 Ranger - sold
94 302 Ranger AWD - sold
07 BMW 335xi - tuned, boost turned up, E85 - sold
04 911 TT - to many mods to list. Over 600 All Wheel HP on pump gas - sold
2015 Coyote - daily driver
03 Cobra - 2.3 TVS on a built 12:1 CR motor with ported heads, cams, long tubes etc.
MD Racing Lean Protection Module
E85
Tuned by MD Racing
https://www.youtube.com/c/MalcolmV8
94 302 Ranger AWD - sold
07 BMW 335xi - tuned, boost turned up, E85 - sold
04 911 TT - to many mods to list. Over 600 All Wheel HP on pump gas - sold
2015 Coyote - daily driver
03 Cobra - 2.3 TVS on a built 12:1 CR motor with ported heads, cams, long tubes etc.
MD Racing Lean Protection Module
E85
Tuned by MD Racing
https://www.youtube.com/c/MalcolmV8