'94 ranger "dash" wiring
Moderator: MalcolmV8
-
MalcolmV8
- Supporting Member
- Posts: 2597
- Joined: Fri Dec 10, 2004 4:50 pm
- SM: Yes
- Location: Kansas City, MO
CJ, do you have a tach?
92 302 Ranger - sold
94 302 Ranger AWD - sold
07 BMW 335xi - tuned, boost turned up, E85 - sold
04 911 TT - to many mods to list. Over 600 All Wheel HP on pump gas - sold
2015 Coyote - daily driver
03 Cobra - 2.3 TVS on a built 12:1 CR motor with ported heads, cams, long tubes etc.
MD Racing Lean Protection Module
E85
Tuned by MD Racing
https://www.youtube.com/c/MalcolmV8
94 302 Ranger AWD - sold
07 BMW 335xi - tuned, boost turned up, E85 - sold
04 911 TT - to many mods to list. Over 600 All Wheel HP on pump gas - sold
2015 Coyote - daily driver
03 Cobra - 2.3 TVS on a built 12:1 CR motor with ported heads, cams, long tubes etc.
MD Racing Lean Protection Module
E85
Tuned by MD Racing
https://www.youtube.com/c/MalcolmV8
-
cjcnomor4
- Posts: 665
- Joined: Fri Dec 10, 2004 5:43 pm
- SM: No
- Location: Spring Hill, FL (1 hour N of Tampa)
yeah, it'll be over the center a/c vents or mounted the the roof at the a-pillar. one of those 5" jobs with an led shift light. i'm 5'5" so if i cant see with it on the center of the dash, it'll go up. may depend on the seats too.
95 2wd shortbed styleside with a 98 mountaineer 5.0
ported GT-40P heads, E-303 cam, Trick Flow Street Heat intake, 1.7 rollers, 24lb injs,155lph in-tank pump, built AOD, 2800 converter, Torque Monster headers, dropped 3/4 on 98 Cobra wheels. Eternal work in progress.
94 Ranger XLT b. 6/10/94 d.3/28/11 300,842 miles RIP
06 Fusion SEL
11 F150 FX2 SCrew 5.0 Coyote, Custom SCT X3 tune, Roush CAI
ported GT-40P heads, E-303 cam, Trick Flow Street Heat intake, 1.7 rollers, 24lb injs,155lph in-tank pump, built AOD, 2800 converter, Torque Monster headers, dropped 3/4 on 98 Cobra wheels. Eternal work in progress.
94 Ranger XLT b. 6/10/94 d.3/28/11 300,842 miles RIP
06 Fusion SEL
11 F150 FX2 SCrew 5.0 Coyote, Custom SCT X3 tune, Roush CAI
-
94stranger
- Posts: 357
- Joined: Wed Jun 20, 2007 1:16 pm
- SM: No
- Location: Toronto, ON, Canada
-
cjcnomor4
- Posts: 665
- Joined: Fri Dec 10, 2004 5:43 pm
- SM: No
- Location: Spring Hill, FL (1 hour N of Tampa)
I used two sheets of aluminum. on the bottom there are leds mounted then on the back side of the top sheet the cutouts from the old gauges. there are small spacers epoxyed between the layers to keep the light from bleeding around the cutouts. the leds are wired in as the bulbs were originally, just had to add some resistors (thanks again to all that got me through that mess) to keep the leds off when they were not supposed to be on. that was only a problem on the ground side switched leds. the gauges go through both sheets. the sheets are bolted to the skeleton of the original cluster, and the original cluster mask is mounted on the outside to clean it up. there is no plastic lens on the outside, i didnt like the tripmeter reset hole in the middle. I did make two connectors to make it removeable and not just a bunch of spades since alot of the wires are the same color. I dont know if that makes any sense, I can pull it out and take some pics but it may not be until next weekend.
95 2wd shortbed styleside with a 98 mountaineer 5.0
ported GT-40P heads, E-303 cam, Trick Flow Street Heat intake, 1.7 rollers, 24lb injs,155lph in-tank pump, built AOD, 2800 converter, Torque Monster headers, dropped 3/4 on 98 Cobra wheels. Eternal work in progress.
94 Ranger XLT b. 6/10/94 d.3/28/11 300,842 miles RIP
06 Fusion SEL
11 F150 FX2 SCrew 5.0 Coyote, Custom SCT X3 tune, Roush CAI
ported GT-40P heads, E-303 cam, Trick Flow Street Heat intake, 1.7 rollers, 24lb injs,155lph in-tank pump, built AOD, 2800 converter, Torque Monster headers, dropped 3/4 on 98 Cobra wheels. Eternal work in progress.
94 Ranger XLT b. 6/10/94 d.3/28/11 300,842 miles RIP
06 Fusion SEL
11 F150 FX2 SCrew 5.0 Coyote, Custom SCT X3 tune, Roush CAI
-
94stranger
- Posts: 357
- Joined: Wed Jun 20, 2007 1:16 pm
- SM: No
- Location: Toronto, ON, Canada
If I could get some pics I think that would be great but I am not in no rush so take your time, especialy since were suspose to get almost 30 cm of snow by tonight! I would appreciate it though if I could get some pics, I think I understand what you mean for the lights put the plastic picture thing between the two plates so it can be seen through the the hole
'93 ranger ext cab 5.0L HO lorider
-
cjcnomor4
- Posts: 665
- Joined: Fri Dec 10, 2004 5:43 pm
- SM: No
- Location: Spring Hill, FL (1 hour N of Tampa)
bingo
95 2wd shortbed styleside with a 98 mountaineer 5.0
ported GT-40P heads, E-303 cam, Trick Flow Street Heat intake, 1.7 rollers, 24lb injs,155lph in-tank pump, built AOD, 2800 converter, Torque Monster headers, dropped 3/4 on 98 Cobra wheels. Eternal work in progress.
94 Ranger XLT b. 6/10/94 d.3/28/11 300,842 miles RIP
06 Fusion SEL
11 F150 FX2 SCrew 5.0 Coyote, Custom SCT X3 tune, Roush CAI
ported GT-40P heads, E-303 cam, Trick Flow Street Heat intake, 1.7 rollers, 24lb injs,155lph in-tank pump, built AOD, 2800 converter, Torque Monster headers, dropped 3/4 on 98 Cobra wheels. Eternal work in progress.
94 Ranger XLT b. 6/10/94 d.3/28/11 300,842 miles RIP
06 Fusion SEL
11 F150 FX2 SCrew 5.0 Coyote, Custom SCT X3 tune, Roush CAI