To avoid fitment problems, might want to look into a modified T-5 by Astro Performance or a G Force unit.
Dave
Search found 1524 matches
- Mon Aug 17, 2015 9:56 am
- Forum: V8 Ranger General Discussion
- Topic: 5 Speed Transmission Question
- Replies: 5
- Views: 10047
- Mon Jul 13, 2015 10:03 am
- Forum: V8 Ranger General Discussion
- Topic: 9 inch for ranger
- Replies: 10
- Views: 16482
Re: 9 inch for ranger
How to do the Mustang rear brakes on an 8.8 rear end. http://www.fordrangerforum.com/engine-d ... -rear.html.
Dave
Dave
- Sat Jun 20, 2015 3:37 pm
- Forum: V8 Ranger General Discussion
- Topic: 9 inch for ranger
- Replies: 10
- Views: 16482
Re: 9 inch for ranger
There are no 9" Pintos and even then they are too narrow. I do happen to have one that came out of a Pinto but it also had a built 351. Another option is to use the 31 spline center chunk from Mustang/Explorer and have custom axles with the 31 spline and the smaller out board bearing journal, t...
- Sat Jan 31, 2015 5:37 pm
- Forum: V8 Ranger General Discussion
- Topic: 331 V8 in a 98 and above Ranger help
- Replies: 3
- Views: 8610
Re: 331 V8 in a 98 and above Ranger help
I know of some that have swapped the old body onto the newer chassis but not the other way around. Any 302/5.0 will fit but using the front dress from the Explorer makes it a lot easier. Same goes for using the later V-8 CPU and engine harness. It's a plug and play when using the 99-2001 Explorer en...
- Sat Nov 22, 2014 11:06 am
- Forum: V8 Ranger General Discussion
- Topic: V8 swap dilemma, with VSS.
- Replies: 5
- Views: 12771
Re: V8 swap dilemma, with VSS.
Plug and play is about it. Only splicing or re-pinning is required in the harness that feeds the A/C and starter relay. Real easy to see if you have both the wiring diagrams.
Dave
Dave
- Wed Nov 19, 2014 4:51 pm
- Forum: V8 Ranger General Discussion
- Topic: V8 swap dilemma, with VSS.
- Replies: 5
- Views: 12771
Re: V8 swap dilemma, with VSS.
I knew I had just seen the same question, just took me a while to find it,
Dave
http://www.therangerstation.com/forums/ ... p?t=157045
Dave
http://www.therangerstation.com/forums/ ... p?t=157045
- Sun Nov 16, 2014 5:05 pm
- Forum: V8 Ranger General Discussion
- Topic: V8 swap dilemma, with VSS.
- Replies: 5
- Views: 12771
Re: V8 swap dilemma, with VSS.
Welcome to the site Bob, we're small but fun. I have the '98' Ranger and the '97' Explorer wiring both scanned it. What parts do you need? The Explorer signal from the VSS is the same as the Ranger I believe, just comes from a different source. Wiring not my field of expertice but others will sure j...
- Fri Oct 03, 2014 9:45 am
- Forum: V8 Ranger General Discussion
- Topic: Cam lift
- Replies: 25
- Views: 36687
Re: Cam lift
I think the difference in the lift is just which ratio rocker is used. Summit says cam is for use with the 1.7's but don't know why. 1.6 ratio is .512 lift. YouTube has several clips of Mustangs running that cam (or the -14 instead of the -12).
Dave
http://www.youtube.com/watch?v=Pnb0ahcdIr4
Dave
http://www.youtube.com/watch?v=Pnb0ahcdIr4
- Sat Sep 27, 2014 6:30 pm
- Forum: V8 Ranger General Discussion
- Topic: trying to figure out what year to go with
- Replies: 10
- Views: 18487
Re: trying to figure out what year to go with
Chris, a lot do go with the rear Mustang brakes for the increased "performance", not looks. I don't buy into cost effective increase of braking. A good set of drum brakes work pretty good from my experience. The earlier Rangers use the same shoes as what some of the 60's performance Fords ...
- Fri Sep 26, 2014 5:32 pm
- Forum: V8 Ranger General Discussion
- Topic: My AOD trans is pooched..
- Replies: 4
- Views: 9138
Re: My AOD trans is pooched..
I was going to say that with a trans in good condition, it's usually the improper adjustment of the cable that causes failure.
Dave
Dave
- Tue Sep 23, 2014 5:34 pm
- Forum: V8 Ranger General Discussion
- Topic: trying to figure out what year to go with
- Replies: 10
- Views: 18487
Re: trying to figure out what year to go with
You can change your stock 8.8 Ranger rear end to run the stronger 31 spline axles with the right carrier and Mosler axles and do the Mustang disc brake conversion if wanted. I myself think rear disc in a truck is not needed. Quite a few running the V-8 have no problem with the rear springs, all depe...
- Mon Sep 22, 2014 9:22 am
- Forum: V8 Ranger General Discussion
- Topic: trying to figure out what year to go with
- Replies: 10
- Views: 18487
Re: trying to figure out what year to go with
All '98'+ 4x4's were torsion bar suspension. Some 4x2's could be had with torsion also depending on model, Trailheads and Sports. All other 4x2's got the coil suspension. One of the limiting factors in the later Rangers is the lack of header options unless custom over the frame versions.
Dave
Dave
- Thu Sep 18, 2014 5:39 pm
- Forum: V8 Ranger General Discussion
- Topic: its back alive
- Replies: 20
- Views: 35874
Re: its back alive
I've seen blocks let go with between 450-500 hp, some an take a lot more.
Dave
Dave
- Wed Sep 17, 2014 1:13 pm
- Forum: V8 Ranger General Discussion
- Topic: its back alive
- Replies: 20
- Views: 35874
Re: its back alive
That looks real good, think the block will hold together? Just for giggles, post up what all you have in it.
Dave
Dave
- Wed Sep 10, 2014 4:31 pm
- Forum: For Sale
- Topic: Front Dress from a 5.0 Explorer
- Replies: 0
- Views: 29567
Front Dress from a 5.0 Explorer
Listing for a friend.
Both brackets( AC/Alternator and power steering pump. Ps pump is still in bracket) , all tensioners and idlers included, timing cover, harmonic balancer and cast oil pan. 150$ plus shipping
kevincoffey13@yahoo.com
Near Dalton, GA
Both brackets( AC/Alternator and power steering pump. Ps pump is still in bracket) , all tensioners and idlers included, timing cover, harmonic balancer and cast oil pan. 150$ plus shipping
kevincoffey13@yahoo.com
Near Dalton, GA